Присоединяйтесь к Нам

Вступайте в нашу группу

facebook/ventumplus

Звоните Нам

Телефон/Факс

+99871 295 1817

Свяжитесь с Нами

Техническая поддержка

info@ventumplus.com

FASAFER - фасадная шпатлевка, купить в Ташкенте | Сместь для выравнивания фасада

FASAFER - фасадная шпатлевка, купить в Ташкенте | Сместь для выравнивания фасада

Façade plastic wood filler FASAFER

Dry mix based on cement, mineral finely divided fillers and modifying additives. The mixture is intended for leveling facades, as well as waterproof plaster, concrete, brick, gas-concrete bases for painting and wallpapering. Intended for internal and external works.

FEATURES:

High strength

Plastic properties

High grindability

PREPARATION OF PRIMARY STRUCTURE: The temperature of the primary structure and the environment should be in the range from +5⁰С to +30⁰С. The primary structure must be strong, thoroughly cleaned of dust, dirt, oils, fats, residues of loose paint and other substances that can weaken the adhesion of the putty layer to the primary structure. Irregularities deeper than 4 mm must be pre-leveled with plaster mixes. Uneven or highly absorbent substrates should be pre-treated with a deep penetration primer. 

PREPARATION OF MORTAR: 

To prepare FASAFER solution, you must:

1. Take a precisely measured amount of water (6.6-7.4 liters per 20 kg bag);

2. Pour the mixture into water;

3. Stir using construction mixer or drill with a special nozzle until a homogeneous mass is obtained;

4. Withstand a technological pause of 5-10 minutes for maturation of the solution;

5. Stir the solution repeatedly.

After this, the putty is ready for use within 3 hours with periodic stirring.

OPERATIONAL PROCEDURE:  Plastic wood filler is applied to the primary structure using a smooth steel spatula. To smooth out small areas, a spatula with the width of 30 cm is used. The permissible thickness of one layer at continuous filling is not more than 4 mm. If it is necessary to apply thicker layers, the solution is applied in several layers with the time intervals necessary for hardening of the previous layer. Drying out time of one layer is from 4 to 8 hours (depending on thickness of a coating layer, temperature and humidity). After drying, the surface is grinded using a thin polishing sheet or sanding mesh. Uncured material is washed off with water. Hardened substances are peeled off mechanically. Attention! Water after cleaning the tool cannot be used to prepare the filler.

OCCUPATIONAL SAFETY: The dry mix contains cement. When mixed with water, the product gives an alkaline reaction. To prevent skin irritation, avoid contact with exposed areas of the body. In case of contact with eyes, rinse immediately with water and consult a doctor if necessary. In addition to the above information, you should be guided by the safety instructions in construction.

WARRANTY AND STORAGE: Warranty period of storage in intact original packaging is 6 months from the date of manufacture. Shelf life is 12 months. Store in dry rooms, excluding ingress of moisture on bags with dry mix. Transportation of products should be carried out under conditions ensuring safety of packaging and protection against moisture. Store a maximum of 10 bags vertically. The instruction for use of dry mix is ​​advisory in nature and does not replace professional training of a contractor. If the instructions and recommendations for storage and use are not followed, the manufacturer is not responsible for the quality of the work performed.

SPECIFICATIONS:

Color: gray

Maximum grain size: 0.315 mm.

Solution lifetime: 3 hours

Drying out time: 4-8 hours

Application layer thickness: 0.6 - 4.0 mm.

Consumption per m² at a layer thickness of 1 mm: 1.0 - 1.3 kg.

Adhesion: 0.8 MPa.

Frost resistance, cycles: 50.

Work temperature: from +10°С to +30°С.

Operating temperature: from -50°С to +70°С.