Присоединяйтесь к Нам

Вступайте в нашу группу

facebook/ventumplus

Звоните Нам

Телефон/Факс

+99871 295 1817

Свяжитесь с Нами

Техническая поддержка

info@ventumplus.com

FUGA SILICON

FUGA SILICON

Dry mix based on white cement binder, mineral fillers, fractionated sand, pigments and modifying additives that improve operational properties.

RANGE OF APPLICATION: Trowel finishis designed to fill joints from 4 to 16 mm wide between wall and floor ceramic tiles, for pools, marble and ceramic-granite tiles, mosaics both inside buildings in rooms with different levels of humidity, and outside buildings. It is used on non-deformable surfaces. For external and internal works in rooms with various level of humidity.

FEATURES:

Low water absorption.

The width of the joint is 4-16 mm.

Steady color.

Water resistance.

PREPARATION OF PRIMARY STRUCTURE: The temperature of the primary structure and environment should be within the range from + 5°C to + 30°C. After laying tiles it is necessary to clean joints between the tiles from the solution used when laying the tiles (tile adhesive). The depth between the tile joints should be the same. Then the surface of the tile cladding must be cleaned of dirt and dust. Hardened contaminants are removed mechanically and dust with a damp soft cloth. Before filling in tile joints in order to avoid changing the color of rubbing in the joints, make sure that the solution used for laying the tiles is dry. Drying time is indicated in the instructions for its use. After that, the edges of the tiles must be moistened with a damp sponge. When updating the seams of the existing tile cladding before applying a new rubbing, the old one must be completely removed.

PREPARATION OF MORTAR: 

To prepare VENTUM FUGA solution, you must:

1. Take a precisely measured amount of water (4.0-4.4 liters per 20 kg).

2. Pour the mixture into water.

3. Mix with a construction mixer or drill with a special nozzle until a homogeneous mass is obtained.

4. Make a technological pause of 10 minutes for the solution to mature.

5. Stir the solution repeatedly.

After this, trowel finish is ready for use within 40 minutes with periodic stirring.

OPERATIONAL PROCEDURE: The solution is applied using a rubber spatula or hand float trowel to the surface of the coating material and rubbed into the seams, moving the tool at the angle to the plane of application. Then the excess mortar mixture is collected with a spatula from the surface of the tile and the tile joints are re-filled again. After 10-20 minutes, the treated surface is wiped with a damp sponge. After 4-6 hours, dry deposit remaining on the surface of the tile should be removed with a dry soft cloth. Attention! Joints for 7 days should be protected from weathering, as it can affect hardening process of the trowel finish.

OCCUPATIONAL SAFETY: The dry mix contains cement. When mixed with water, the product gives an alkaline reaction. To prevent skin irritation, avoid contact with exposed areas of the body. In case of contact with eyes, rinse immediately with water and consult a doctor if necessary. In addition to the above information, you should be guided by the safety instructions in construction.

WARRANTY AND STORAGE: Warranty period of storage in intact original packaging is 6 months from the date of manufacture. Store in dry rooms, excluding ingress of moisture on bags with dry mix. Transportation of products should be carried out under conditions ensuring safety of packaging and protection against moisture. Store a maximum of 10 bags vertically. If the instructions and recommendations for storage and use are not followed, the manufacturer is not responsible for quality of the work.    

SPECIFICATIONS: 

Maximum grain size, mm: 0.63

Solution lifetime, min.: 40

Width of a joint, mm: from 4 to 16

Mixture consumption depends on the joint width and tile size, kg/m²: 0.4 - 0.8

Work temperature: from + 5°С to + 30°С

Drying out time: 6h

Compressive Strength, MPa: 13

Frost resistance not less than, cycles: 50

Operating temperature: from -50°С to + 70°С.